| Official Luthiers Forum! http://www-.luthiersforum.com/forum/ |
|
| Neck wood http://www-.luthiersforum.com/forum/viewtopic.php?f=10102&t=10447 |
Page 1 of 1 |
| Author: | outstrung [ Thu Jan 18, 2007 2:45 am ] |
| Post subject: | |
I have been looking for what type of woods can be used on acoustic necks. I usually see just Spanish Cedar or Mahogany. But many suppliers carry more than just those two woods. Are other woods such as rosewood (besides the cost and rarity) Also goo for necks. If not why? Thanks - Adam |
|
| Author: | Dave Rector [ Thu Jan 18, 2007 3:30 am ] |
| Post subject: | |
Maple and walnut both make excellent necks. Rosewood is used for necks as well but it is pretty heavy. If I was making a choice I would consider the weight of the neck very carefully. Other than that anything that is stable and that you think you can carve well is fair game. |
|
| Author: | Colin S [ Thu Jan 18, 2007 3:49 am ] |
| Post subject: | |
Cherry is a great neck wood as well. Colin |
|
| Author: | John How [ Thu Jan 18, 2007 4:04 am ] |
| Post subject: | |
I think maybe when I can no longer use mahogany, I'll try walnut, or maybe I'll quit. |
|
| Author: | SimonF [ Thu Jan 18, 2007 4:54 am ] |
| Post subject: | |
Adam, Walnut works very well and isn't all that heavy. I think it is a good substitute for mahogany. I built a guitar with a wenge neck. Wenge is a very heavy wood. I noticed a substantial improvement in sustain when using wenge, especially in the lower registers. Dropping the guitar into DADGAD and plucking with normal force results in over 26 seconds of sustain - which is pretty darn good. So be aware that going with a very dense and heavy wood like wenge or indian rosewood will affect the sound. I think a heavy neck wood is an excellent option for those that play in alternate tunings or purely fingerstyle. |
|
| Author: | Mattia Valente [ Thu Jan 18, 2007 5:16 am ] |
| Post subject: | |
Also, while indian rosewood is heavy, it's not actually terribly stiff for its weight... Walnut, Cherry, Mahogany, Maple, list goes on and on and one. I plan on making some rosewood necks for my electrics, but not for my acoustics. |
|
| Author: | Serge Poirier [ Thu Jan 18, 2007 2:08 pm ] |
| Post subject: | |
How about cocobolo necks? Anyone tried this? |
|
| Author: | Eric Mathre [ Fri Jan 19, 2007 3:19 am ] |
| Post subject: | |
I noticed that LMI now carries Sapele neck blanks (although they're currently out of stock). Somewhere on some forum I read a comment from someone who was very pleased with Sapele as a Honduras Mahogany replacement. Anyone here have direct experience? |
|
| Author: | Mattia Valente [ Fri Jan 19, 2007 4:42 am ] |
| Post subject: | |
Oh, certainly the African mahoganies can make great necks; Sapele is possibly my favourite neck wood, a little heavier than most mahoganies (mostly), plenty stiff, great stuff. Khaya can also be great, but it's more variable (the heavier stuff I have is much stiffer than the lightweight, and is perfectly excellent for necks as well). Sipo/Utile mahogany can be great too. Serge: David Myka (electric builder) builds with Cocobolo necks, loves it, and has inspired me to build myself a personal (electric) guitar with a Cocobolo neck. For an acoustic, once again, I worry about the sheer mass of such an item. |
|
| Author: | Serge Poirier [ Fri Jan 19, 2007 4:50 am ] |
| Post subject: | |
Thanks Mattia, i had the weight factor in mind too but on the aesthetic side, must be really gorgeous! |
|
| Author: | outstrung [ Sun Jan 21, 2007 3:02 pm ] |
| Post subject: | |
Thanks for all the info! |
|
| Author: | martinedwards [ Sun Jan 21, 2007 11:38 pm ] |
| Post subject: | |
I've used walnut, mahogany and some other stuff I salvaged from a dumpster whick I later ID'd as possibly Port Orford Cedar!!!!! 
Made a dread and a mando with this as neck wood and no problems yet over 6 months down the line......... Not a fan of CARVING the walnut, And I tried oak but it was horrible to carve. As long as mahogany is available (questionable) or I can scrounge old table tops I'll stick with it. |
|
| Author: | Arnt Rian [ Mon Jan 22, 2007 12:09 am ] |
| Post subject: | |
Oak and ash should make fine necks (remember that gorgeous 000 12 fretter by John Kinnaird with curly ash neck and appointments? O-la-la!), but perhaps on the heavy side for 14 fret acoustics. Hickory and beech has tremendous strength, but the weight would be even higher. Birch has been used a lot, many of the classic Gibson mandolins (and most likely guitars too) had birch necks, sides and backs. I'm sure that many of the common hardwoods will work, but as long as we still can get mahogany... |
|
| Author: | Sam Price [ Mon Jan 22, 2007 4:49 am ] |
| Post subject: | |
I'll second (or third) the cherry. Lovely to carve, tough on the tools... Mahogany is amazing. It is such a tough, forgiving wood!!! |
|
| Author: | LouisianaGrey [ Mon Jan 22, 2007 9:36 am ] |
| Post subject: | |
Of the ones I've used, Bubinga is nice but heavy. Zebrano ditto, combined with the Wenge problems of open pores and grain that goes in different directions. |
|
| Author: | outstrung [ Mon Jan 22, 2007 6:52 pm ] |
| Post subject: | |
Awesome, its nice to hear that other people have wondered and tried rather than just going with the flow. |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|